Cloud DCM-1 User's Guide Page 28
- Page / 68
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
DCM-1 User Manual v1.0
Installation
26
3rd.-party Paging systems
The DCM-1 may be integrated with any paging system which
is able to provide a microphone feed and zone selection by
contact closure.
Paging microphone input
A three pin Phoenix-type connector provides an
electronically-balanced input for an external paging
microphone. This should be connected to the external
microphone using good quality low-noise microphone cable,
using the wiring shown below:
12v phantom power is available at the input for microphones
requiring external power (e.g. electret mics). Phantom
power is enabled by the internal jumper J24. The default
setting for this jumper is with phantom power OFF; move
the jumper to the other position to set phantom power ON.
See page 51 for details of jumper locations.
Adjusting paging levels
Separate controls are available at the rear panel for setting
microphone sensitivity and the paging level sent to each
Zone. Full details on adjusting these can be found at page 44.
Paging Access Connector
The Paging Access connector is used to activate the paging
microphone and to select the zone(s) to which it is to be
routed. It performs this function by default, though it can be
re‑dened in the menu system to provide per‑zone control
outputs when used with Cloud CDPM paging microphones
(see page 25). (Should a system require the use of both
CDPM and third-party paging systems, control outputs will
not be available if the connector is to be used in its “input”
mode.)
Zone activation occurs when one of the “zone active” pins
(2 - 9) is shorted to 0v (available on pin 1). Third-party
paging systems providing per‑zone contact‑closure on zone
selection can thus be easily interfaced by wiring the external
unit to the Paging Access connector as shown below:
The pinout is the same as that given in page 25. Multicore
control cable should be used for the interconnection.
Some 3rd.-party paging systems have a single “page-all”
command output, which activates all zones in use. In this
case, use the wiring scheme shown at ii) above.
PAGING ACCESS CONNECTOR
+12v1
0
v
865
4
3
2 7
PAGE ZONE 1
PAGE ZONE 8
PAGE ZONE 7
PAGE ZONE 6
PAGE ZONE 5
PAGE ZONE 4
PAGE ZONE 3
PAGE ZONE 2
3RD-PARTY
PAGING SYSTEM
i) Individual zone paging
PAGING ACCESS CONNECTOR
+
12v
1
0
v
86
5
4
3
2
7
3RD-PARTY
PAGING SYSTEM
ii) Page-All only
1
2
3
:
1 2 3
+
-
+
-
SCN
pin 1 ground
pin 2 hot
pin 3 cold
Balanced mic:
pin 1 ground
pin 2 cold
pin 3 hot
DCM-1 Paging
Microphone input:
Paging mic wiring
- Digitally Controlled Mixer 1
- Installation and User Guide 1
- Contents 4
- DCM-1 User Manual v1.04 6
- Introduction 7
- What’s in the box 8
- Section 1 : Overview 9
- System Components 10
- Optional components 10
- Overview 11
- System Block Diagram 13
- Applications and Examples 14
- Section 2 : Installation 17
- Description of rear panel 18
- Hardware considerations 19
- System Connections 19
- Installation 20
- Network diagram 1 21
- Network diagram 3 22
- Network diagram 2 22
- Note Jumper J1 not shown 23
- Mic/Line input plates 24
- Connecting Paging systems 26
- PAGING ACCESS CONNECTOR 28
- Paging mic wiring 28
- Front Panel Centre Section 31
- User Menu Flow Diagram 32
- Music Menu Flow Diagram 33
- Conguration 34
- Routing Menu Flow Diagram 35
- System Menu Flow Diagram 37
- Priorities Menu Flow Diagram 41
- 42
- Groups Menu Flow Diagram 45
- PAGING MICROPHONE INPUT 46
- PAGING LEVEL 46
- CDR-1 Remote Control Plates 47
- Normal Mode Installer Mode 48
- DCM-1 User Manual v1.0 47 49
- System Interconnections 51
- Line Inputs 51
- Section 4 : Appendix 53
- RS232 Serial Control 54
- PSU capability 55
- RJ45 pinouts 56
- Fitting Bose 56
- Series II EQ cards 56
- Firmware updates 56
- Factory default settings 57
- EMC considerations 57
- Specications 58
- User Conguration 59
- Notes Overleaf 59
- DCM‑1 Conguration Notes 60
- (to be left with the User) 60
- Installer Conguration 61
- Appendix 62
- DCM-1 User Manual v1.062 64
- DCM-1 User Manual v1.0 63 65
- DCM-1 User Manual v1.064 66
Related products and manuals for Mixers Cloud DCM-1
Mixers Cloud DCM-1 User Manual
(68 pages)
(68 pages)
© 2020, manymanuals.com. All rights reserved. | 1.389 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals